Shenzhen Guyukang Technology Co.,Ltd.

Products

Molds Exhibit
Plastic Shell Mould
Toy Moulds
Plastic Products
Transparent plastic products
Lens
Mould for Home Appliance Parts
Panel Structure

Plastic mould explain with Chinese and English

Plastic mould explain with Chinese and English

一、入水:gate                               

 进入位: gate location

 水口形式:gate type

 大水口:edge gate

 细水口: pin-point gate

 水口大小:gate size

 转水口: switching runner/gate

 唧嘴口径: sprue diameter

 

二、流道: runner                             

 

 

 热嘴冷流道: hot sprue/cold runner

 唧嘴直流: direct sprue gate

 圆形流道:round (full/half runner)

 流道电脑分析:mold flow analysis

 流道平衡:runner balance

 热嘴: hot sprue

 热流道板:hot manifold

 发热管:cartridge heater

 探针: thermocouples

 插头: connector plug

 插座: connector socket

 密封/封料: seal

 

三、运水:water line                             

 

 喉塞:line lpug

 喉管:tube

 塑胶管:plastic tube

 快速接头:jiffy quick connector plug/socker

 

 四、模具零件: mold components               

 三板模:3-plate mold

 二板模:2-plate mold

 边钉/导边:leader pin/guide pin

 边司/导套:bushing/guide bushing

 中托司:shoulder guide bushing

 中托边L:guide pin

 顶针板:ejector retainner plate

 托板: support plate

 螺丝: screw

 管钉:dowel pin

 开模槽:ply bar scot

 内模管位:core/cavity inter-lock

 顶针: ejector pin

 司筒:ejector sleeve

 司筒针:ejector pin

 推板:stripper plate

 缩呵:movable core,return core core puller

 扣机(尼龙拉勾):nylon latch lock

 斜顶:lifter

 模胚(架): mold base

 上内模:cavity insert

 下内模:core insert

 行位(滑块): slide

 镶件:insert

 压座/斜鸡:wedge

 耐磨板/油板:wedge wear plate

 压条:plate

 撑头: support pillar

 唧嘴: sprue bushing

 挡板:stop plate

 定位圈:locating ring

 锁扣:latch

 扣鸡:parting lock set

 推杆:push bar

 栓打螺丝:S.H.S.B

 顶板:eracuretun

 活动臂:lever arm

 分流锥:spure sperader

 水口司:bush

 垃圾钉:stop pin

 隔片:buffle

 弹弓柱:spring rod

 弹弓:die spring

 中托司:ejector guide bush

 中托边:ejector guide pin

 镶针:pin

 销子:dowel pin

 波子弹弓:ball catch

 喉塞: pipe plug

 锁模块:lock plate

 斜顶:angle from pin

 斜顶杆:angle ejector rod

 尼龙拉勾:parting locks

 活动臂:lever arm

 复位键、提前回杆:early return bar

 气阀:valves

 斜导边:angle pin

 术语:terms

 承压平面平衡:parting surface support balance

 模排气:parting line venting

 回针碰料位:return pin and cavity interference

 模总高超出啤机规格:mold base shut hight

 顶针碰运水:water line interferes withejector pin

 料位出上/下模:part from cavith (core) side

 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

 

 不准用镶件: Do not use (core/cavity) insert

 用铍铜做镶件: use beryllium copper insert

 初步(正式)模图设计:preliinary (final) mold design

 反呵:reverse core

 弹弓压缩量:spring compressed length

 稳定性好:good stability,stable

 强度不够:insufficient rigidity

 均匀冷却:even cooling

 扣模:sticking

 热膨胀:thero expansion

 公差:tolorance

 铜公(电极):copper electrode

 热流道: hot runner,hot manifold