深圳市谷雨康科技有限公司|联兴精密模具制品厂0755-29491490|透明塑胶外壳|玩具模具

产品中心

模具展示
塑胶外壳模具
玩具类模具
塑胶类产品
透明塑胶产品
镜片展示
家电类样品
手板结构件

塑料模具中英文解释大全

塑料模具中英文解释大全

一、入水:gate                               

 进入位: gate location

 水口形式:gate type

 大水口:edge gate

 细水口: pin-point gate

 水口大小:gate size

 转水口: switching runner/gate

 唧嘴口径: sprue diameter

 

二、流道: runner                             

 

 

 热嘴冷流道: hot sprue/cold runner

 唧嘴直流: direct sprue gate

 圆形流道:round (full/half runner)

 流道电脑分析:mold flow analysis

 流道平衡:runner balance

 热嘴: hot sprue

 热流道板:hot manifold

 发热管:cartridge heater

 探针: thermocouples

 插头: connector plug

 插座: connector socket

 密封/封料: seal

 

三、运水:water line                             

 

 喉塞:line lpug

 喉管:tube

 塑胶管:plastic tube

 快速接头:jiffy quick connector plug/socker

 

 四、模具零件: mold components               

 三板模:3-plate mold

 二板模:2-plate mold

 边钉/导边:leader pin/guide pin

 边司/导套:bushing/guide bushing

 中托司:shoulder guide bushing

 中托边L:guide pin

 顶针板:ejector retainner plate

 托板: support plate

 螺丝: screw

 管钉:dowel pin

 开模槽:ply bar scot

 内模管位:core/cavity inter-lock

 顶针: ejector pin

 司筒:ejector sleeve

 司筒针:ejector pin

 推板:stripper plate

 缩呵:movable core,return core core puller

 扣机(尼龙拉勾):nylon latch lock

 斜顶:lifter

 模胚(架): mold base

 上内模:cavity insert

 下内模:core insert

 行位(滑块): slide

 镶件:insert

 压座/斜鸡:wedge

 耐磨板/油板:wedge wear plate

 压条:plate

 撑头: support pillar

 唧嘴: sprue bushing

 挡板:stop plate

 定位圈:locating ring

 锁扣:latch

 扣鸡:parting lock set

 推杆:push bar

 栓打螺丝:S.H.S.B

 顶板:eracuretun

 活动臂:lever arm

 分流锥:spure sperader

 水口司:bush

 垃圾钉:stop pin

 隔片:buffle

 弹弓柱:spring rod

 弹弓:die spring

 中托司:ejector guide bush

 中托边:ejector guide pin

 镶针:pin

 销子:dowel pin

 波子弹弓:ball catch

 喉塞: pipe plug

 锁模块:lock plate

 斜顶:angle from pin

 斜顶杆:angle ejector rod

 尼龙拉勾:parting locks

 活动臂:lever arm

 复位键、提前回杆:early return bar

 气阀:valves

 斜导边:angle pin

 术语:terms

 承压平面平衡:parting surface support balance

 模排气:parting line venting

 回针碰料位:return pin and cavity interference

 模总高超出啤机规格:mold base shut hight

 顶针碰运水:water line interferes withejector pin

 料位出上/下模:part from cavith (core) side

 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.

 

 不准用镶件: Do not use (core/cavity) insert

 用铍铜做镶件: use beryllium copper insert

 初步(正式)模图设计:preliinary (final) mold design

 反呵:reverse core

 弹弓压缩量:spring compressed length

 稳定性好:good stability,stable

 强度不够:insufficient rigidity

 均匀冷却:even cooling

 扣模:sticking

 热膨胀:thero expansion

 公差:tolorance

 铜公(电极):copper electrode

 热流道: hot runner,hot manifold